Technical Requirements of Bitumen Emulsion
(CATIONIC TYPE) IS: 8887:2004
(CLAUSES 4.2 AND 6.2)
Characteristics |
Grades of Emulsion |
Method of Test, Ref to |
||||
| RS-1 | RS-2 | MS | SS-1 | SS-2 | IS No/ Annex of this standard | |
| Residue on 600 micron RIS Sieve, percent by mass, Max | 0.05 | 0.05 | 0.05 | 0.05 | 0.05 | Annex B |
| Viscosity by saybolt furol viscometer, seconds: | IS:3117 | |||||
| 1) At 25 Deg. C | - | - | - | 20-100 | 30-150 | |
| 2) At 50 Deg. C | 20-100 | 100-300 | 50-300 | - | - | |
| Coagulation of emulsion at low temperature C | Nil | Nil | Nil | Nil | Nil | Annex C |
| Storage stability after 24 h, percent, Max | 2 | 1 | 1 | 2 | 2 | Annex D |
| Particle charge | Positive | Positive | Positive | Positive | Positive | Annex E |
| Coating ability and water resistance: | ||||||
| 1. Coating, dry aggregate | - | - | Good | - | - | Annex F |
| 2. Coating, after spraying | - | - | Fair | - | - | |
| 3. Coating, wet aggregate | - | - | Fair | - | - | |
| 4. Coating, after spraying | - | - | Fair | - | - | |
| Stability to mixing with cement (percentage coagulation), Max | - | - | - | - | 2 | Annex G |
| Miscibility with water | No coagulation | No coagulation | No coagulation | No coagulation | No coagulation | Annex H |
| Tests on residue: | ||||||
| 1. Residue by evaporation, percent, Min. | 60 | 67 | 65 | 60 | Annex J | |
| 2. Penetration 25 Deg. C/100g/5 sec | 80-150 | 80-150 | 60-150 | 60-120 | IS 1203 | |
| 3. Ductility 27 Deg. C/cm, Min. | 50 | 50 | 50 | 50 | IS 1203 | |
| 4. Solubility : In trichloro-ethylene, Percent by mass, Min. | 98 | 98 | 98 | 98* | 98 | IS 1216 |
| Distillation in percent, by volume at 3600 C at | ||||||
| 1. 1900 C | - | - | - | 20-55 | - | IS 1203 |
| 2. 2250 C | - | - | - | 30-75 | - | |
| 3. 2600 C | - | - | - | 40-90 | - | |
| 4. 3150 C | - | - | - | 60-100 | - | |
| 5. Residue at 360 C%, Min. | - | - | - | 50 | - | |
| Water content, percent by mass,Max. | - | - | - | 20 | - | IS 1211 |
| Note 1: “This requirement shall be applicable only under situations where the ambient temperatures is below 15 Deg. C. | ||||||
| * The Value of solubility is determined on distillation residue at 360o C | ||||||
RS-1 : Rapid Setting – 1
RS-2 : Rapid Setting – 2
MS : Medium Setting
SS-1 : Slow Setting – 1
SS-2 : Slow Setting - 2

